Multichannel Ceramic
R&D Membrane System
Introducing our new benchtop membrane filtration systems with ceramic membranes. A complete solution for advanced membrane filtration with ceramic membranes. Empowered with integrated measurement technologies, our membrane filtration system is the ideal tool for researching and advancing membrane filtration processes.
Multichannel Ceramic Membrane Elements
Ceramic microfiltration and ultrafiltration elements offer improved chemical and thermal resistance and a longer service life compared to polymers. The porous membranes are made of ceramic materials such as aluminum oxide (Al2O3), zirconium oxide (ZrO2), silicon carbide (SiC), titanium dioxide (TiO2), etc. These materials are used to produce membranes in various shapes such as tubes, plates, discs or multi-channel elements.Compatible with all ⌀ 25 mm ceramic elements across all suppliers
The laboratory system is compatible with multi-channel elements from all manufacturers, diameter 25 mm, length 500, 600, 1200 mm. Channel diameter: 1.5...6 mm. We offer an extensive selection of these elements for applications in microfiltration and ultrafiltration. A → design guide supports you in the selection of elements.
P&ID
Specification
Pump Pressure
Hygienic diaphragm pump, stainless steel, PEEK, EPDM, medium 0 °C to 95 °C, adjustable 0...10 bar, 0 - 5 V / 0 - 10 V, 4 - 20 mA, 24 VDC
Pump Circulation
Centrifugal pump, AISI 316L, 220V / 50Hz, adjustable speed, 3/4" clamp connections
Pump Backflow
Hygienic diaphragm pump, stainless steel, PEEK, EPDM, medium 0 °C to 95 °C, adjustable 0...10 bar, 0 - 5 V / 0 - 10 V, 4 - 20 mA, 24 VDC
Heat-Exchanger
Multi-channel heat exchanger, AISI 316L, clamp, PN10
Control Valve
CTV_01CTV_02
Hygienic control valves, adjustable 0...100 %, 0...10 VDC
Flowmeter
FT_01FT_02
Principle: ultrasonic, signal 4...20 mA, 24 VDC
Pressure Transmitter
PT_01PT_02PT_03PT_04
Principle: piezoresistive, hygienic design with flush diaphragm, measuring range: 0...10 bar, 4...20 mA
Conductivity
CT_01
Conductivity measurement, 0...150 mS/cm, 24 VDC, 4...20 mA
Refractometer
XT_01
Refractometer, 1.3330 - 1.5000 nD20, 24 VDC, 4...20 mA
Level
LT_01LT_02
Continuous fill level, 24 VDC, 4...20 mA
Sensors and Actuators
Flow meter
Ultrasonic flow meter, output 4...20 mA. Measures the flow rate of permeate and retentate with high accuracy.
Measuring cell
Measuring cell with various connections (image: Clamp ASME 1/2") for connecting additional sensors or as an interface for atline devices.
Control valve
Control valve for precise flow control on the permeate side.
Atline valve block
Changeover valves, feed permeate into an external analyzer.
Inline, Atline
With the concept of inline-measurement, sensors are installed in the pipes. In the atline circuit, the permeate flow is forwarded to an external laboratory device (analyzer).
In inline analysis, the sensor is positioned either in a process tank or on the pipeline. The measuring system is an integral part of the filtration system. In at-line analysis, the sample volume is transported to the measuring device near the filtration system. The measuring system is located outside the filtration system. The sample is not returned to the process.
Software
The software has a modern and user-friendly layout. With the software, users can reduce analysis time and determine time-based correlations via batch and continuous processes. In addition, measurement methods and controls can be optimized. The intuitive open-source software can be further developed by the operator without licenses in order to adapt to changing issues and requirements.
Control Box
The control box (AISI 304, IP 65) has various M12 connections for the sensors and actuators.
USB connectors
Main switch
Status indicators (LED)
Power cable
M12 plugs